CHIEF.
Web appLearnPlatformFeaturesFor employers
UTC --:--:--Open web app
Web appLearnPlatformFeaturesFor employersContact
Open web appiOS app on the App Store →Android app on Google Play →
Learn/ECR — Engine Control Room/Guides

Ballasting through the ballast water treatment system

CHIEF. LEARN · Guide 6 of 7

Starting a UV ballast water treatment system for ballasting: power, warm-up, treated volume, UV transmittance and the Ballast Water Record Book entry.

The example throughout is the engine control room of a Supramax bulk carrier: three diesel generators on a 440 V, 60 Hz main switchboard with a bus-tie and a power management system, an emergency generator feeding the emergency switchboard, the main engine controlled from the ECR console, and a UV ballast water treatment system.

MSB
main switchboard
MCCB
moulded-case circuit breaker
BWTS
ballast water treatment system
UVT
UV transmittance: how much ultraviolet light gets through the water

Why the ship treats its ballast

Ballast water carries organisms from one port to the next. Under the IMO Ballast Water Management Convention every ship manages its ballast to a standard set out in a ship-specific plan, and carries a Ballast Water Record Book and an International Ballast Water Management Certificate.

Most ships meet the discharge standard with a type-approved BWTS. The system in the trainer filters the water and treats it with ultraviolet light on the way into the tanks.

The scenario: no power to the BWTS

In the trainer the BWTS will not start. Its MSB feeder, the moulded-case breaker BALLAST WATER TREATMENT on 440 V feeder panel No.2, was left OFF after maintenance.

The fault is common on board: a system that has not run since a job was done on it. Before you look for a fault in the equipment, check that it has power.

Step by step

  1. Find why the BWTS has no power and switch its MSB feeder ON: MCCB BALLAST WATER TREATMENT on 440 V feeder panel No.2.
  2. Start the BWTS in BALLAST mode on its remote panel, on the forward bulkhead to the left of the engine room door.
  3. Wait for the UV lamps to warm up. The status changes to BALLAST · TREATING.
  4. Treat at least 300 m³, watching the treated volume on the BWTS display. If the UV transmittance alarm comes, acknowledge it.
  5. Stop the BWTS with a normal STOP. The operation is written to the system log for the Ballast Water Record Book entry.

UV transmittance

UV light only treats what it reaches. In muddy or coloured harbour water less of it gets through, and the UV transmittance (UVT) falls.

To keep the dose the organisms receive, the system reduces the flow. Ballasting takes longer, and the trainer raises an alarm when the UVT is low. If the system cannot hold its dose, the water is not treated to the standard.

The record

Every ballast operation goes into the Ballast Water Record Book: when, where, how much and how it was treated. A port State control officer reads it next to the system’s own log.

A treatment that stopped is recorded too. In the trainer a power failure during ballasting stops the treatment and says so: POWER FAILURE — treatment stopped, record in the Ballast Water Record Book.

Try it in the simulator. Parallel a generator, bring the plant back after a blackout and start the main engine in a walk-in 3D engine control room, with a score for each scenario. Free, in your browser on a computer, with a free CHIEF. account.

Open ECR — Engine Control Room →

Check yourself

The BWTS will not start after maintenance. What do you check first?
  1. That its feeder on the MSB is switched on — correct
  2. The UV lamps
  3. The ballast pump impeller

In the trainer the MCCB was left OFF after maintenance. Power first, then the equipment.

What happens when the UV transmittance of the water is low?
  1. The system reduces the flow to keep the dose — correct
  2. The system treats faster
  3. Nothing changes

Less UV gets through murky water, so the system slows the flow so each litre still gets its dose.

Sources

  • Ballast Water Management: how to do it (IMO publication I624E)

For training only. The room, the switchboard and the sequences are simplified; class rules, the makers’ manuals and your company’s procedures are the authority.

← PreviousOil mist detector: the weekly function testNext →Lock-out / tag-out in the engine room
Built by CHIEF.

Free for seafarers: CV, certificates, sea service

These trainers are made by CHIEF., the career platform for seafarers. Keep your STCW certificates with expiry reminders, log sea service and send a ready CV to crewing companies.

Free to startiPhone, Android, any browserOne account
Create a free accountiOS app on the App Store →Android app on Google Play →

Already have an account? The button opens it.

CHIEF.
LearnCertificate trackerCV builderSeafarer CVSTCW certificatesSea-time calculatorCountry guidesWeb appiOS appAndroid appContact
© 2026 CHIEF. · Maritime Reconnected
support@chief.directPrivacyTermsUAru